XtremepowerUS 12-inch Sand Filter Pump System (Model 75110-V) Instruction Manual

1. Introduktion

This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your XtremepowerUS 12-inch Sand Filter Pump System. Please read this manual thoroughly before attempting to install or operate the system. Keep this manual for future reference.

Figure 1: XtremepowerUS 12-inch Sand Filter Pump System in operation.

Säkerhetsföreskrifter

• Koppla alltid bort strömmen innan du utför någon form av service eller underhåll.
• Ensure the system is installed on a level surface.
• Do not operate the pump dry. Ensure it is primed with water before starting.
• Håll barn borta från pumpen och filtersystemet under drift.
• This pump is not for use/sale in California.

2. Paketets innehåll

Kontrollera att alla komponenter som listas nedan ingår i ditt paket. Om några delar saknas eller är skadade, vänligen kontakta kundsupport.

Figur 2: Alla komponenter ingår i paketet.

• Sandfiltertank (12 tum)
• 0.75 HP Pool Pump
• 4-vägs flerportsventil
• Tryckmätare
• System Tray / Mounting Base
• Slangadaptrar
• Slangar och kloramps
• Manuell

3. Specifikationer

Key technical specifications for the XtremepowerUS 12-inch Sand Filter Pump System:

Figur 3: Produktens mått.

4. Installation och installation

Follow these steps carefully to assemble and install your sand filter pump system. Refer to the video for visual guidance.

4.1 Filteraggregat

1. Montera dräneringsmunstycket: Place an O-ring onto the long side of the filter drain nozzle. Route the nozzle from inside the filter barrel and push it out through the bottom drain hole. Place another O-ring and secure it with the nut from outside the barrel. Insert an O-ring into the drain hole nozzle cap and screw it onto the nozzle.
2. Position Filter Assembly: Place the filter assembly inside the filter barrel. Position the funnel on top of the filter assembly, ensuring it is correctly inserted and centered within the barrel.
3. Fyll med filtermedia: Fill the filter barrel with your chosen filter media (filter balls or sand) according to recommended guidelines. Remove the funnel after filling.
4. Install 4-Way Valve: Place an O-ring onto the 4-way valve. Position the valve on the upper part of the filter, ensuring the top of the filter assembly is properly inserted into the bottom of the valve. Ensure the valve pump opening aligns with the filter stand groove and the waste opening is oriented towards the drain nozzle. Secure the valve in place with the locking ring. Place the square nut on one side of each locking ring and tighten.
5. Installera tryckmätare: Secure the pressure gauge with plumber's tape. Remove the pressure gauge covering screw from the valve and screw the pressure gauge onto the valve.

4.2 Pumpinstallation

1. Position Pump on Base: Place the pump on top of the system tray (mounting base), aligning it with all four screw holes.
2. Säker monteringsbas: Flip the mounting base over and insert all four nuts into the mounting spaces. Carefully flip the mounting base back.
3. Fasten Pump: Place the bolts into the screw holes and tighten all four bolts with a Phillips screwdriver to secure the pump to the base.
4. Install Pump Adapters: Put O-rings on the hose adapters and screw the hose adapters onto the pump outlet and inlet.

4.3 Hose Installation

Se till att all slang clamps are securely tightened to prevent leaks. Verify O-rings are correctly seated.

1. Filter to Pump Connection: Placera en slang clamp on the hose adapter from the valve opening marked 'PUMP'. Connect a hose to this adapter and then to the pump's inlet hose adapter. Tighten both hose clamps.
2. Pool Return to Valve Connection: Connect the hose from the pool's return inlet to the hose adapter from the valve opening marked 'POOL'. Ensure the O-ring on the hose adapter is not displaced during this process. Tighten the hose clamp.
3. Pool Main Drain to Pump Connection: Connect the hose from the pool's main drain to the hose adapter on the pump's outlet. Tighten the hose clamp.

5. Drift

The 4-way multi-port valve allows for different operational modes. Always ensure the pump is OFF before changing valve settings.

Figure 4: Multi-port valve settings.

Valve Modes:

• Filtrering: This is the standard operating mode. Water is pumped from the pool, filtered through the sand media, and returned to the pool.
• Backwash: Used to clean the filter media. Water flow is reversed, flushing trapped debris out through the waste port. Perform backwash when the pressure gauge reading is 8-10 PSI above the clean filter reading.
• Skölj: After backwashing, this mode settles the filter media and removes any remaining dirt from the filter lines before returning to filtration mode.
• Avfall: Drains water directly from the pool, bypassing the filter. Useful for lowering pool water level or vacuuming heavy debris directly to waste.
• Återcirkulera: Circulates pool water without filtering.
• Vinter: Used for winterizing the system.

6. Underhåll

Regelbundet underhåll säkerställer optimal prestanda och livslängd för ditt filtersystem.

6.1 Backspolning

Backwash the filter when the pressure gauge indicates a rise of 8-10 PSI above its normal clean operating pressure. This typically means the filter media is saturated with debris.

1. Stäng av pumpen.
2. Set the multi-port valve to 'BACKWASH'.
3. Turn on the pump and run until the water from the waste port runs clear (typically 1-2 minutes).
4. Stäng av pumpen.
5. Set the multi-port valve to 'RINSE'.
6. Slå på pumpen och kör den i 30–60 sekunder.
7. Stäng av pumpen.
8. Set the multi-port valve back to 'FILTRATION'.
9. Slå på pumpen för att återgå till normal drift.

6.2 Cleaning the Pump Strainer Basket

The pump's strainer basket should be checked and cleaned regularly to prevent debris from entering the pump impeller.

Figure 5: Pump strainer basket.

1. Stäng av pumpen och stäng alla nödvändiga ventiler för att förhindra vattenflöde.
2. Unscrew the clear lid of the strainer basket.
3. Ta bort korgen och töm allt uppsamlat skräp.
4. Rinse the basket thoroughly.
5. Replace the basket and securely screw the lid back on. Ensure the O-ring is properly seated to prevent air leaks.
6. Open valves and prime the pump if necessary before restarting.

6.3 Byte av filtermedia

Sand filter media typically lasts 3-5 years, depending on usage and water quality. Filter balls may require more frequent cleaning or replacement.

1. Stäng av pumpen och koppla bort strömmen.
2. Drain the filter tank completely.
3. Remove the multi-port valve.
4. Carefully remove the old filter media.
5. Rinse the inside of the tank.
6. Add new filter media, ensuring the standpipe is centered.
7. Reassemble the valve and reconnect all hoses.
8. Perform a backwash and rinse cycle before resuming normal filtration.

7. Felsökning

Det här avsnittet behandlar vanliga problem som du kan stöta på med ditt sandfilterpumpsystem.

8. Garanti och support

For warranty information or technical support, please refer to the warranty card included with your product or visit the XtremepowerUS official webwebbplats. Spara ditt inköpskvitto som inköpsbevis för eventuella garantianspråk.