IXITAB KWS-AC301/KWS-AC300
Instruktionsmanual
KWS-AC301/KWS-AC300 Digital Power Energy Meter
1. Introduktion
This manual provides detailed instructions for the installation, operation, and maintenance of the IXITAB KWS-AC301/KWS-AC300 Digital AC Power Energy Meter. This device is designed to accurately measure and display AC voltage, current, active power, energy (kWh), and temperature. It is suitable for monitoring electrical parameters in various AC circuits.
2. Säkerhetsinformation
VARNING: Electrical shock hazard. Installation and servicing should only be performed by qualified personnel. Failure to follow these instructions may result in serious injury or death.
- Se till att strömförsörjningen är frånkopplad före installation eller kabeldragning.
- Överskrid inte den angivna volymentage and current ratings (AC 50-300V, 100A).
- Använd inte enheten i vått eller damp villkor.
- Håll enheten borta från brandfarliga material.
- Kontrollera att alla anslutningar är säkra och korrekta innan du slår på strömmen.
3. Produkt överview
The KWS-AC301/KWS-AC300 meter features a clear digital display for simultaneous monitoring of multiple electrical parameters. It is compact and designed for easy integration into electrical panels or systems.
Figure 3.1: Product image placeholder. This image indicates that a specific product image is not available. The actual product is a compact digital meter designed for AC electrical measurements.
Nyckelfunktioner inkluderar:
- Real-time measurement of AC Voltage (V), ström (A), aktiv effekt (W) och energi (kWh).
- Temperaturdisplay.
- High accuracy and stability.
- Lättläst digital display.
4. Installation och kabeldragning
Before proceeding, ensure the main power supply is OFF.
- Montering: Choose a suitable location for the meter, typically within an electrical panel or enclosure, ensuring adequate ventilation.
- Voltage Input (L/N): Anslut AC voltage input wires to the designated L (Live) and N (Neutral) terminals on the meter. Ensure the voltage ligger inom intervallet 50–300 V AC.
- Anslutning av strömtransformator (CT):
- Pass the load wire (the wire carrying the current you wish to measure) through the hole of the external current transformer (CT).
- Connect the two small wires from the CT to the dedicated CT input terminals on the meter. Pay attention to polarity if indicated, though many simple CTs are non-polar for measurement.
- Lastanslutning: Ensure the load is correctly connected to the circuit being monitored.
- Ström på: After all connections are verified and secure, restore power to the circuit. The meter should power on and display readings.
Note: The CT must be connected before applying power to the meter to avoid damage. Do not disconnect the CT while power is applied to the meter.
5. Bruksanvisning
Once powered on, the KWS-AC301/KWS-AC300 meter will automatically begin displaying the measured parameters. The display typically cycles through or shows simultaneously:
- Voltage (V): Visar aktuell AC-volymtage.
- Aktuell (A): Displays the current AC amperage flowing through the monitored circuit.
- Aktiv effekt (W): Displays the instantaneous active power consumed by the load.
- Energi (kWh): Accumulates the total energy consumed over time. This value is typically non-volatile and retained even after power loss.
- Temperatur (°C/°F): Displays the ambient temperature measured by the device.
Some models may include a button for resetting the energy (kWh) reading. If present, press and hold the button for approximately 5 seconds to clear the accumulated energy data. Refer to specific product markings for button functionality.
6. Underhåll
The KWS-AC301/KWS-AC300 meter requires minimal maintenance.
- Rengöring: Använd en mjuk, torr trasa för att rengöra skärmen ochasing. Använd inte slipande rengöringsmedel eller lösningsmedel.
- Inspektion: Kontrollera regelbundet kabelanslutningarna för att säkerställa att de sitter ordentligt fast.
- Lagring: If storing the device for an extended period, keep it in a dry, cool environment, away from direct sunlight and extreme temperatures.
7. Felsökning
| Problem | Möjlig orsak | Lösning |
|---|---|---|
| Ingen display/Mätaren slås inte på | Ingen strömförsörjning; felaktig kabeldragning; defekt enhet. | Check power connections. Verify L/N wiring. Ensure power is applied. If problem persists, contact support. |
| Incorrect current reading (0A or very low) | CT not connected; CT connected incorrectly; load wire not passed through CT. | Ensure CT is properly connected to the meter. Verify the load wire passes through the CT. Do not disconnect CT while powered. |
| Felaktig voltage läsning | Felaktig voltage input wiring; voltage utanför angivet intervall. | Check L/N voltage input connections. Ensure voltage är inom 50-300V AC. |
| Energy (kWh) not accumulating | No current flow; faulty unit. | Ensure there is an active load drawing current. Verify current reading is non-zero. |
8. Specifikationer
| Parameter | Värde |
|---|---|
| Modell | KWS-AC301 / KWS-AC300 |
| Operation Voltage Räckvidd | AC 50-300V |
| Nuvarande räckvidd | 0-100A |
| Mätparametrar | Voltage, Current, Active Power, Energy (kWh), Temperature |
| Paketets mått | 1.18 x 0.79 x 0.39 tum |
| Objektets vikt | 1.76 uns |
| Tillverkare | IXITAB |
| ASIN | B0CSWFLZFL |
| Datum först tillgängligt | 20 januari 2024 |
9. Garanti och support
This product is manufactured by IXITAB. For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly through the platform where the product was purchased. Please have your purchase details and product model number (KWS-AC301/KWS-AC300) ready when contacting support.
For further assistance, you may refer to the product listing on Amazon.com.