RGBlink NDI PTZ Camera Controller (RGBBKT) User Manual

1. Introduktion

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of the RGBlink NDI PTZ Camera Controller (RGBBKT). This device is designed for professional video production environments, offering comprehensive control over various PTZ cameras using multiple protocols.

Image 1.1: RGBlink NDI PTZ Camera Controller (RGBBKT).

2. Inställning

Follow these steps to set up your RGBlink NDI PTZ Camera Controller.

2.1 Uppackning och första inspektion

• Ta försiktigt ut alla komponenter ur förpackningen.
• Kontrollera att alla artiklar som anges i packlistan finns med.
• Inspect the controller for any signs of physical damage. If damage is found, contact your dealer immediately.

2.2 Ansluta styrenheten

The RGBlink NDI PTZ Camera Controller supports various connection methods for power and camera control.

• Power over Ethernet (PoE): Connect a single RJ45 Ethernet cable from a PoE-enabled network switch to the controller's LAN port. This provides both power and network connectivity.
• Extern strömadapter: If PoE is not available, connect the provided power adapter to the DC 12V input port and to a power outlet.
• Kameraanslutningar:
  • Ethernet (IP Control): Connect PTZ cameras to the same network as the controller via RJ45 Ethernet cables. The controller supports VISCA over IP, ONVIF v2.42, and NDI v5.5 protocols.
  • Serial Control: For cameras supporting serial communication, use RS232, RS422, or RS485 interfaces. Connect the appropriate cables from the controller's serial ports to the cameras.

Image 2.1: Rear panel connections including RS-232, RS-422, LAN (PoE), and Power Input.

Bild 2.2: Example connection diagram showing PTZ Controller, PoE Switch, PTZ Cameras, Audio Mixer, and Computer.

Image 2.3: Diagram illustrating IP camera connections via a network switch.

2.3 Nätverkskonfiguration

For IP-based camera control, ensure the controller and cameras are on the same network segment. The controller supports automatic detection of NDI-enabled PTZ cameras.

• Access the controller's web gränssnitt genom att ange dess IP-adress i en web browser. (Refer to the device's display or network tools to find the IP address).
• The default login credentials are typically 'admin' with a blank password. It is recommended to set a strong password immediately.
• Inom web interface, configure camera protocols (e.g., ONVIF, VISCA over IP) and enter camera-specific user credentials if required.

Image 2.4: NDI|HX camera search and control interface on the controller.

3. Drift

This section details the operational functions of the RGBlink NDI PTZ Camera Controller.

3.1 Överview av kontroller

The controller features a 3.49" LCD display, a 3D joystick, various knobs, and a numeric keypad for intuitive control.

Image 3.1: The controller's 3.49-inch LCD display.

Bild 3.2: Detaljerad view of the 3D joystick and multi-function knobs.

Image 3.3: Layout of the controller's buttons and numeric keypad area.

3.2 Kameraval

• Snabbvalsknappar: Use the dedicated CAM 1-5 buttons for quick selection of up to 5 cameras.
• Numerisk knappsats: For cameras beyond the quick select buttons (up to 255), press the CAM -ID button, then enter the camera number using the numeric keypad, and press SKRIVA IN.

Image 3.4: The controller's ability to manage multiple cameras.

3.3 PTZ-kontroll

• joystick: The 3D joystick controls pan (left/right), tilt (up/down), and zoom (rotate the joystick).
• PT hastighetsratt: Adjusts the gimbal movement speed for pan and tilt.
• Zoom Knob: Provides precise zoom control, especially useful in preview läge.

3.4 Image Parameter Adjustment

• IRIS/SHUTTER Knob: Rotate to adjust aperture and shutter speed. Press to switch control modes.
• R/B GAIN Knob: Rotate to adjust red and blue gain. Press to switch control modes.
• FOCUS Button: Tryck på AUTOFOKUS button to switch the camera to auto focus mode.
• EXPOSURE Button: Cycles through exposure modes (Aperture Priority, Shutter Priority, Gain Priority, Manual Exposure, Auto Exposure).
• BAKGRUNDSBELYSNING-knapp: Toggles the camera's backlight mode.
• WHITE BALANCE CYCLE Button: Cycles through white balance modes (Indoor, Outdoor, Manual, Auto).
• ONE PUSH TRIGGER Button: When white balance is set to "One-Push White Balance", press this button to initiate a one-push white balance calibration.

Image 3.5: Functions of buttons and knobs on the left side of the controller.

Image 3.6: Functions of buttons and knobs on the right side of the controller, including preset controls.

3.5 förinställningar

• SET PRESET Button: Press to enter preset position mode. Use the numeric keys to enter the preset number (0-9) and press SKRIVA IN att spara. Tryck ESC att gå ur.
• CALL PRESET Button: Press to enter preset recall mode. Use the numeric keys to enter the preset number (0-9) and press SKRIVA IN to recall. Press ESC att gå ur.
• The controller supports saving and recalling up to 255 presets per camera.

3.6 Menynavigering

• MENU-knapp: Press to open or close the camera settings menu. In menu control mode, the joystick controls navigation (up, down, left, right), SKRIVA IN confirms selections, and ESC acts as a back button.

4. Underhåll

Proper maintenance ensures the longevity and optimal performance of your RGBlink NDI PTZ Camera Controller.

4.1 Rengöring

• Use a soft, dry cloth to clean the exterior of the controller.
• För envis smuts, lätt dampSkölj trasan med vatten eller ett milt, icke-slipande rengöringsmedel.
• Avoid using harsh chemicals, solvents, or abrasive materials, as these can damage the surface and display.
• Ensure no liquids enter the device through openings or ports.

4.2 Förvaring

• När den inte används under längre perioder, förvara kontrollenheten på en sval, torr plats borta från direkt solljus och extrema temperaturer.
• Skydda enheten från damm och fukt.

5. Felsökning

Det här avsnittet innehåller lösningar på vanliga problem som du kan stöta på.

5.1 Ingen ström

• Kontrollera strömkällan: Se till att nätadaptern är ordentligt ansluten till både kontrollenheten och ett fungerande eluttag.
• PoE Check: If using PoE, verify that the Ethernet cable is connected to a PoE-enabled port on your network switch and that the switch is powered on.
• Kabelintegritet: Inspect the power cable and Ethernet cable for any damage.

5.2 Cannot Control Camera

• Nätverksanslutning: For IP cameras, ensure the controller and cameras are on the same network and can communicate. Check network cables and IP addresses.
• Protokollfel matchar: Verify that the correct control protocol (e.g., VISCA over IP, ONVIF, NDI, Pelco-D/P) is selected on both the controller and the camera.
• Kamera-ID: Ensure the correct camera ID is selected on the controller.
• Inloggningsuppgifter: If the camera requires authentication, confirm that the correct username and password are configured in the controller's web gränssnitt.
• Seriell anslutning: For serial control, check RS232/RS422/RS485 cable connections and ensure baud rates and addresses match between the controller and camera.
• Firmware: Ensure both the controller and cameras have the latest firmware installed. Visit the RGBlink support webwebbplats för uppdateringar.

5.3 LCD Display Issues

• Ingen skärm: Se till att styrenheten är påslagen.
• Dim display: Check if there are any brightness settings on the controller that can be adjusted.

6. Specifikationer

Image 6.1: Controller dimensions and typical usage environments.

Image 6.2: Visual representation of supported protocols including RJ45, RS485, RS422, RS232, ONVIF, NDI, Pelco-D, Pelco-P, and Visca.

7. Produktvideodemonstration

Watch the official product video for a visual demonstration of the RGBlink NDI PTZ Camera Controller's features and operation.

8. Garanti och support

For warranty information, technical support, or service inquiries, please contact RGBlink customer service or visit their official webplats.

• Tillverkare: Xiamen RGBlink Science & Technology Co., Ltd.
• Officiell Webplats: www.rgblink.com (Obs: Detta är en platsmarkör URL, please refer to your product packaging or official documentation for the correct support webplats.)
• Kontaktinformation: Refer to the RGBlink official website for the most current contact details for technical support and warranty claims.