AIYIMA TPA3116 Subwoofer Amplifier Board Användarmanual

Introduktion

This manual provides detailed instructions for the AIYIMA TPA3116 Subwoofer Amplifier Board, a high-performance 2.1 channel digital audio amplifier. It features Bluetooth 5.0 connectivity and adjustable controls for a customized audio experience. Please read this manual carefully before installation and operation to ensure proper usage and optimal performance.

Drag

• Utilizes TI's TPA3116D2 high-performance digital power amplifter-chip.
• 2.1 channel output: 100W for bass channel, 50W for left channel, and 50W for right channel.
• Supports Bluetooth 5.0 audio reception for wireless connectivity.
• Includes an external audio input interface (AUX).
• Features a preamplifier and dedicated bass crossover processing.
• Equipped with 5 adjustment potentiometers for precise control: Bass Volume, Bass Frequency, Left and Right Channel Volume, Treble, and a Function Control Switch/Total Volume.
• Bred drift voltage-område: DC 12-25V.
• Energy-saving design with efficiency up to 90%.
• The board is pre-soldered and tested for immediate use.
• Subwoofer cut-off frequency: 26-160Hz.

Specifikationer

Notera: The output power is directly related to the supply voltage/current, speaker impedance, and the level of the audio input. Higher supply voltage/current generally allows for greater output power. Speakers with lower impedance are typically easier to drive to higher power levels.

Paketets innehåll

• 1 x AIYIMA TPA3116 Bluetooth Subwoofer Amplivligare styrelse

Inställning

1. Strömanslutning

• Connect a DC power supply within the 12-25V range to the DC power input terminal (labeled 'DC IN').
• Ensure correct polarity: positive (+) to positive, negative (-) to negative.
• The recommended power supply is DC24V 4.5A. For high power requirements, use 20-24V with 8-9A or higher current.
• Försiktighet: The DC no-load voltage must not exceed 25.5V to prevent damage to the board.

2. Anslutning för ljudingång

• De amplifier supports both Bluetooth and AUX audio input.
• For wired input, connect your audio source (e.g., smartphone, PC, turntable) to the 'AUX IN' port using a 3.5mm audio jack or the 3-pin audio input terminal.

3. Högtalarutgång

• Connect your left and right channel speakers to the 'Lout' and 'Rout' terminals. Ensure speaker impedance is 4-8 ohms.
• Connect your subwoofer speaker to the 'Subwoofer output' terminals. Ensure subwoofer impedance is 2-8 ohms.
• Viktig: The left and right channel speaker (+) and (-) outputs are independent and must not be connected to each other or short-circuited.

Bruksanvisning

Kontrollerna överview

• Master Volume / Function Switch (Red Knob): Turn left/right to adjust the overall volume. Press down to switch between Bluetooth and AUX input modes.
• Treble Frequency Knob: Justerar ljudets högfrekvensrespons.
• L/R Channel Volume Knob: Adjusts the volume specifically for the left and right stereo channels.
• Bass Frequency Knob: Adjusts the crossover frequency for the bass output.
• Bass Volume Knob: Justerar volymnivån för subwooferutgången.
• Full Frequency Bass Switch: Toggles the full frequency bass on or off.
• LED-indikator: Provides visual feedback on the amplifier's status (e.g., blinking for Bluetooth pairing, solid for connected).

Function Switch Usage

1. Vid påslagning, amplifier defaults to Bluetooth mode. The LED indicator will typically blink, indicating it's ready for pairing.
2. To switch to AUX audio input mode, ensure Bluetooth is disconnected, then long-press the Master Volume / Function Switch knob.
3. When in Bluetooth play status, a short press of the Master Volume / Function Switch knob will pause or play the audio.

Bluetooth-parning

1. Se till att amplifier is powered on and in Bluetooth mode (LED blinking).
2. Aktivera Bluetooth på din ljudenhet (smartphone, surfplatta etc.) och sök efter tillgängliga enheter.
3. Välj amplifier (usually named 'AIYIMA TPA3116' or similar) from the list to pair and connect.
4. Once connected, the LED indicator will typically become solid.

Användar Tips

• Optimal strömförsörjning: For best performance, especially at higher volumes, use a 24V power supply with a current rating of 8-10A. Laptop power supplies (e.g., 19V) can also work effectively.
• Minimera buller: To reduce current noise or hum, ensure your power supply has good filtering. Using high-quality, shielded audio input cables and avoiding shared power sources with other audio equipment can also help.
• AUX Input Activation: If you're having trouble with the AUX input, make sure Bluetooth is disconnected from the amplifier, then long-press the master volume knob to switch to AUX mode.
• Högtalarkompatibilitet: Medan amplifier supports 4-8 ohm speakers for L/R channels and 2-8 ohm for the bass channel, be cautious with very low impedance speakers (e.g., 1 ohm) at maximum volume, as this may trigger the amplifier's protection circuits.
• Power Output Considerations: The actual power output you achieve will depend on your power supply's voltage and current, the impedance of your speakers, and the input level of your audio source.
• Power-On Click/Pop: A slight click or pop upon power-on can be normal. If it's excessively loud, check your power supply unit (PSU) for stability.
• Överhettningsskydd: Om amplifier cuts out during extended use, it might be due to overheating protection. Ensure adequate ventilation and that your speaker impedance and power supply are within recommended limits.

Felsökning

1. No Sound Output or Sound in Only One Channel

• Check Speaker Connections: Ensure all speaker wires are securely connected to the correct terminals and that the speakers themselves are functional.
• Verify Input Cable: Inspect the audio input cable for damage and ensure it's properly plugged into both the ampljudkällan.
• Audio Source Output: Confirm that your audio source device is playing sound and its output volume is adequate.

2. Volume Distortion or Breaking Sound at High Volume

• Insufficient Power Input: Ensure your power supply provides sufficient current (e.g., 8-9A for high power at 20-24V).
• Högtalarbegränsningar: Your speakers might have poor performance, be damaged, or have an incorrect power rating for the amplifiers utgång.
• Incorrect Speaker Wiring: Left and right channel speaker (+) and (-) outputs are independent; do not connect them to each other.

3. Subwoofer Distortion or "Farting" Sound

• Inadequate Power: Ensure the power supply can deliver enough current for the subwoofer channel.
• Subwoofer Issues: The subwoofer itself might have poor bass performance, be damaged, or its enclosure might be unsuitable.

4. Amplifier Burnout

• Omvänd polaritet: Always connect the power supply with correct positive and negative polarity.
• Övervoltage: Överskrid inte den maximala driftsvolymentage på 25.5V.
• AC Power: If using an AC transformer, it must be rectified and converted to DC power before connecting to the amplivligare.
• Kortslutningar: Ensure all wiring is correct and free from short circuits.

5. Problem med Bluetooth-anslutning

• Lägesval: Bekräfta amplifier is in Bluetooth mode (LED blinking for pairing).
• Interferens: Se till att inga andra enheter är aktivt anslutna till ampLifier via Bluetooth.
• Reparation: Try deleting the amplifier from your device's Bluetooth list and re-pairing.

6. AUX Input Not Functioning

• Lägesväxel: Long-press the Master Volume / Function Switch knob to toggle from Bluetooth to AUX input mode.

Underhåll

• Rengöring: Behåll ampRengör skyddsplattan och fritt från damm. Använd en mjuk, torr trasa för rengöring.
• Miljö: Avoid exposing the board to moisture, liquids, or extreme temperatures.
• Ventilation: Ensure proper airflow around the heatsinks to prevent overheating.
• Ändringar: Do not attempt to modify the circuit unless you are a qualified technician. Unauthorized modifications may void any potential warranty and could damage the device.

Garanti och support

For warranty information and technical support, please refer to the seller's contact information or the product packaging. This product is designed for DIY audio enthusiasts. Proper installation and usage are crucial for optimal performance and longevity.