Home › ATOMSTACK › ATOMSTACK L2 Smart Z-Axis Module Installation Guide

Installationsguide för ATOMSTACK L2 Smart Z-axelmodul

ATOMSTACK-L2-Smart-Z-Axis-Module-featured-image

ATOMSTACK L2 Smart Z-axelmodul

Z-axel höjd autojusterare installationsmanual L2-5W/L2-10W/L2-20W/L2-40W

Notera: Bilderna är endast för referens, se den faktiska produkten. För mer information, vänligen skanna QR-koden.

lista

Installationsmetod för Z-axeln

A5 PRO V2/A10 PRO V2

Skruva loss 4 st M4*6 moturs för att ta bort skjutreglaget

Installera A5 Pro V2/A10 Pro V2 dedikerad kontakt
Dra åt 4 st M4*6

A20 PRO V2/A40 PRO V2

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral A48 PRO/A48 Ultra inget behov av att flytta gränslägesbrytarna

Steg 1

Vänd över gravören
Ta bort 2 skruvar från gränslägesbrytarkortet
Flytta brädet framåt för att passa in 2 hål
Lås tillbaka 2 skruvar på kortet
Avsluta
Vänd över gravören

Laser enhetlig installationsmetod

Steg:1 Ta bort 4 st M3 och laserslider
Steg:2 Installera laserskjutaren med 4 M3-skruvar borttagna från steg 1

Obs: Skruva loss fixeringsstycket med en korsskruvmejsel i verktygslådan först, installera sedan laserskjutaren på A48 laser

Kabelanslutningsmetod

Laserinstallationsmetod
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral/ A12 Ultral/A24 Ultral/X12 Ultral/ X24 Ultral

A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2

Notera: När strömmen slås på för att använda Z-axelns höjdautomatik behöver du bara trycka på "autofokus"-knappen på kontrollboxen för att autofokusera lasern

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral

Notera: Skärmen behövs när du använder Z-axelns höjdautomatik, du måste styra den från skärmens ände

Kundservice: För detaljerad garantipolicy, besök vår tjänsteman webwebbplats: www.atomstack.com För teknisk support och service, vänligen maila: support@atomstack.com
Tillverkare: Shenzhen AtomStack Technologies Co.,Ltd
Adress: 17:e våningen, byggnad 3A, fas II, Intelligent Park, nr. 76, Baohe Avenue, Postnummer: tret, Longgang District, Shenzhen, Guangdong, Kina
Skanna QR kod: ELLER kodläsare/streckkodsläsare eller valfri app med skanner

Dokument/resurser

L2 Smart Z-axelmodul

Installation Guide · L2, L2 Smart Z-Axis Module, Smart Z-Axis Module, Z-Axis Module, Module

Referenser

Användarmanualmanual.tools

Published: July 13, 2024

Uppdaterad: 14 juli 2024

Frågor och svar

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Frågor & svar

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

🇺🇸 Robert säger:

23 april 2026 klockan 12:48
I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob
🇺🇸 Robert asks I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob

Manuals+ clarified question

Fråga

How do I connect the L2 Smart Z-Axis Module cable to an ATOMSTACK A20 PRO V2 machine?
Svar

För att ansluta ATOMSTACK L2 Smart Z-axelmodul till din A20 PRO V2, you must use the specific wiring method outlined in the manual for "V2" series machines. The connection does not plug directly into a spare port on the motherboard; instead, it typically involves an adapter or a specific bridge connection.

Enligt Section 05 — Cable connection method for the A20 PRO V2:

X-Axis Connection: The Z-axis module cable usually connects to the transfer board located on the X-axis carriage.

Y-Axis Motor Comparison: While the connector may look similar to a Y-axis motor plug, it is intended for the Z-axis control port. On V2 models, this is often a 4-pin or 6-pin connector located on the breakout board near the laser module mount.

Check for the Adapter: Ensure you are using the "Z-axis connection cable" included in the L2 kit (listed as item 4 in the 01-List). One end connects to the L2 module motor, and the other connects to the reserved Z-axis port on the machine's X-axis terminal.

If the connector physically does not fit any port on the X-axis carriage board, please verify if your kit included a small adapterkort eller a Y-shaped splitter cable, as some V2 revisions require splitting the signal or using a specific conversion interface provided in the L2 box.
Read the full Q&A page
Svar
1. 🇺🇸 Robert säger:
  
  23 april 2026 klockan 2:31
  I don’t know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don’t see any extra ports anywhere .
  🇺🇸 Robert asks I don't know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don't see any extra ports anywhere .
  
  Manuals+ clarified question
  
  Fråga
  
  Where are the transfer board and X-axis terminal located on the ATOMSTACK L2 Smart Z-Axis Module?
  
  Svar
  
  Based on the installation manual for the ATOMSTACK L2 Smart Z-axelmodul, the components you are looking for are part of the cable connection setup (Section 05):
  
  Transfer Board: This is the small PCB (circuit board) located on the back or side of the X-axis carriage (the part that moves left and right). On many AtomStack models like the A6, A12, A24, and X24 series, this board is where the main ribbon cable connects.
  
  X-axis Terminal: This refers to the specific port on that transfer board. For the L2 module, you typically need to plug the Z-axis connection cable into the port labeled for the Z-axis or the auxiliary port on this board.
  
  Notera: If you do not see extra ports, ensure you are looking at the tillbaka of the laser carriage assembly. On some older models (like the A5 Pro or V2 series), the connection method differs and may involve connecting directly to the main control box or using a specific adapter cable included in the L2 kit. Please verify your specific machine model, as the manual shows different wiring paths for the A5/V2 series versus the Pro/Ultra series.
  
  Read the full Q&A page
  Svar
  1. 🇺🇸 Robert säger:
    
    23 april 2026 klockan 2:55
    I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
    
    🇺🇸 Robert asks I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
    
    Manuals+ clarified question
    
    Fråga
    
    Where are the PCB, extra ports, adapters, or splitters for the ATOMSTACK L2 Smart Z-Axis Module?
    
    Svar
    
    Based on the ATOMSTACK L2 Smart Z-Axis Module installation guide, the components included in the box (Section 01 - List) are:
    
    Z-axis height adjuster
    
    Laser slider
    
    A5/P/A10/A20/X20/S20 dedicated connector
    
    M3*6 skruvar
    
    M4*5 skruvar
    
    Z-axis connection cable
    
    Manuell
    
    2.0/2.5 insexnyckel
    
    Korsskruvmejsel
    
    Regarding the PCB and Ports: The L2 module is designed to integrate with existing AtomStack frames. For many models (like the A6 Pro, A12 Pro, A24 Pro, etc.), the connection is made directly to the existing X-axis motor interface or the laser module's connection point using the provided Z-axis connection cable. There is typically no separate external PCB board included in this kit.
    
    Regarding Adapters/Splitters: The manual shows that for certain models (Section 05 - Cable connection method), you must unplug the original X-axis motor cable and connect it to the Z-axis module's interface, or use the dedicated connector provided in the kit. If your specific machine model is not listed in the manual (A5, A10, A20, A6 Pro, etc.), you may require a specific adapter not included in the standard L2 package. If these items are missing from your specific kit, it is recommended to contact support@atomstack.com för verifiering.
    
    Read the full Q&A page
    Svar
    1. 🇺🇸 Robert säger:
      
      23 april 2026 klockan 3:23
      
      Now what do I do ?
      
      🇺🇸 Robert asks Now what do I do ?
      
      Manuals+ clarified question
      
      Fråga
      
      What are the next steps after installing the ATOMSTACK L2 Smart Z-Axis Module?
      
      Svar
      
      Once you have physically mounted the ATOMSTACK L2 Smart Z-Axis Module and connected the cables as shown in the manual, you must configure your software to recognize the new hardware. Follow these steps:
      
      Kabelverifiering: Ensure the Z-axis connection cable is securely plugged into the module and the corresponding port on your laser engraver's motherboard (refer to Section 05 of the manual for your specific model).
      
      Programvarukonfiguration: Open your laser control software (LightBurn or LaserGRBL). You may need to enable the Z-axis in the device settings. In LightBurn, go to Enhetsinställningar and ensure 'Enable Z-Axis' is toggled on.
      
      Fokusering: The L2 module is designed for automatic or simplified focusing. Use the control panel or software commands to move the Z-axis up and down to verify smooth movement before starting a project.
      
      Gränslägesbrytare: If you are using models like the A6 Pro, A12 Pro, or A24 Pro, the manual notes that you do not need to relocate the limit switches.
      
      If the module is not moving, double-check that the 2-pin or 4-pin connectors are not reversed and that your machine's firmware is up to date.
      
      >
      
      Read the full Q&A page
      
      Svar

Ställa en fråga Cancel question

Relaterade ämnen

Modul L2